Analysis of factors affecting the automatic high-frequency induction brazing strength of PDC

Authors

DAI Yongbo, Xi'an Research Institute Co. Ltd., China Coal Technology and Engineering Group Corp., Xi'an 710077, China

Abstract

With the development of automation and intelligentization in manufacturing industry, the research on PDC bit brazing automation is one of the key development directions of bit production technology. In order to study the influencing factors and adaptation methods of welding strength in PDC automatic brazing process, PDC high frequency induction welding and shear strength comparison test were carried out by using PDC and alloy pillar as the base material through special tooling and test conditions. Combined with the shear strength experiment and the morphology of brazing surface of PDC high-frequency induction brazing, the effect of brazing filler alloys, fluxes, surface pretreatment, welding method, heat preservation and induction heating on welding strength was analyzed, and a brazing process suitable for PDC automatic brazing was proposed. The results showed that the suitable silver brazing filler alloys and special solder paste should be selected according to the actual situation; the surface oxide layer of the base metal has a great influence on the brazing strength; the rotary auxiliary welding method is helpful for the spreading of the solder and the exhaust slag, at the same time, this method can effectively improve the strength of induction brazing; the heat preservation has little effect on induction brazing strength of PDC; the influence of skin effect on the edge solder melt while the center solder not melt because of the low temperature should be reduced, which would affect the strength of the work piece.The research results provide a feasible solution for the realization of PDC automatic induction welding, and provide a basis for the realization of PDC bit automatic brazing.

Keywords

PDC bit, automatic, high-frequency induction brazing, brazing strength, influence factors

DOI

10.3969/j.issn.1001-1986.2019.06.033

Recommended Citation

D. (2019) "Analysis of factors affecting the automatic high-frequency induction brazing strength of PDC," Coal Geology & Exploration: Vol. 47: Iss. 6, Article 34.
DOI: 10.3969/j.issn.1001-1986.2019.06.033
Available at: https://cge.researchcommons.org/journal/vol47/iss6/34

Reference

[1] 杨金华,郭晓霞. PDC钻头技术发展现状与展望[J]. 石油科技论坛,2018,37(1):33-38. YANG Jinhua,GUO Xiaoxia. The present status and outlook of PDC bit technology[J]. Oil Forum,2018,37(1):33-38.

[2] 龙伟民,乔培新,丁天然,等. PDC石油钻头钎缝强度的研究[J]. 金刚石与磨料磨具工程,2010,30(5):15-20. LONG Weimin,QIAO Peixin,DING Tianran,et al. Study on the brazing strength of PDC petroleum drill bit[J]. Diamond & Abrasives Engineering,2010,30(5):15-20.

[3] 龙伟民,高雅,何鹏,等. 钎焊技术在金刚石工具中的应用[J]. 焊接,2017(4):10-16. LONG Weimin,GAO Ya,HE Peng,et al. Application of brazing technology to diamond tools manufacturing[J]. Welding & Joining,2017(4):10-16

[4] 龙伟明,乔培新,李涛,等. PCD用钎料及钎焊工艺的研究[J]. 金刚石与磨料磨具工程,2002,22(4):27-29. LONG Weimin,QIAO Peixin,LI Tao,et al. Study on brazing alloy and brazing technology for PDC[J]. Diamond & Abrasives Engineering,2002,22(4):27-29.

[5] 罗蒙丽,硬质合金钎焊技术的现状与发展[J]. 硬质合金,2015,32(2):108-118. LUO Mengli. Current status and development of brazing technology of cemented carbide[J]. Cemented Carbide,2015,32(2):108-118.

[6] 范文捷,刘芳,刘建正,等. 高频感应钎焊钎料、钎剂对PCD刀具焊接性能的影响[J]. 工具技术,2004,38(6):22-24. FAN Wenjie,LIU Fang,LIU Jianzheng,et al. Influence of brazing alloy and soldering acid in high-frequency induction brazing welding for welding performance of PCD cutter[J]. Tool Engineering,2004,38(6):22-24.

[7] 王立,李嫚,贾乾忠,等. 金刚石复合片与硬质合金的钎焊研究[J]. 中国机械工程,2009,20(3):365-369. WANG Li,LI Man,JIA Qianzhong,et al. Study on brazing of diamond compact and cemented carbide[J]. China Mechanical Engineering,2009,20(3):365-369.

[8] 张亚东. PDC刀具高频感应钎焊工艺及机理研究[D] 大连:大连理工大学,2016.

[9] 杨志平,彭凌洲. PCD刀具钎焊工艺研究[J]. 硬质合金,2014,31(5):302-308. YANG Zhiping,PENG Lingzhou. Study on brazing process of PCD Cutting tool[J]. Cemented Carbide,2014,31(5):302-308.

[10] 朱朋飞. PCD刀具高频感应钎焊焊后保温工艺研究[D]. 大连:大连理工大学,2008.

[11] 迟辉,张伟,赵维巍,等. 高频感应钎焊硬质合金接头热处理工艺研究[J]. 稀有金属与硬质合金,2007,35(3):20-22. CHI Hui,ZHANG Wei,ZHAO Weiwei,et al. Study on heat treatment process for HF-induction[J]. Rare Metals and Cemented Carbides,2007,35(3):20-22.

[12] 李卓然,刘兵,樊建新,等. YG8硬质合金和低碳钢的高频感应钎焊[J]. 焊接学报,2010,31(10):97-100. LI Zhuoran,LIU Bing,FAN Jianxin,et al. High-frequency induction brazing of YG8 sintered-carbide to mild steel[J]. Transactions of the China Welding Institution,2010,31(10):97-100.

[13] 刘晓燕. 提高PDC钻头焊接强度工艺研究[J]. 煤田地质与勘探,2004,32(增刊1):192-194. LIU Xiaoyan. Technological study for enhancing the joint intensity of PDC bit[J]. Coal Geology & Exploration,2004,32(S1):192-194.

[14] 万一. 高频感应钎焊工艺参数对钎着率的影响[D]. 重庆:重庆理工大学,2013.

[15] 王适,张弘弢,于宏图. 聚晶金刚石复合片高频感应钎焊的试验研究[J]. 工具技术,2002,36(8):19-22. WANG Shi,ZHANG Hongtao,YU Hongtu. Experimental study on Hi-frequency induction brazing of PCD compacts[J]. Tool Engineering,2002,36(8):19-22.

[16] 王立. PDC刀具高频感应钎焊的研究[D]. 大连:大连理工大学,2007.

[17] 左平英. PDC钻头钎焊工艺的研究[D]. 西安:西安科技大学,2005.

[18] 张素慧,戴勇波,李耿,等. 基于不同母材的PDC钎焊强度的影响因素分析[J]. 煤田地质与勘探,2018,46(6):198-202. ZHANG Suhui,DAI Yongbo,LI Geng,et al. Analysis on the influence factors of brazing strength of PDC based on different base metal[J]. Coal Geology & Exploration,2018,46(6):198-202.

[19] 张启运,庄鸿寿. 钎焊手册[M]. 北京:机械工业出版社,2008.